A gathering place for CCNA's, or those looking to obtain their CCNA! 1) No posting of illegal materials (torrents, stolen PDFs, etc) 2) No posting of 'braindumps' (this includes 9tut) 3) Be courteous and helpful 4) If someone is wrong, try to be clear and understanding in your correction, not rude and disrespectful 5) Do not ask for others to do your labs for you, or solicit payment for labs to be done for you. 6) This sub is not intended for tech support questions, you would be better off asking such questions in or since this sub is by definition a novice community that is trying to learn networking fundamentals. • • Helpful Resources • • - Thank you for pointing it out • • - By Matthew George, CCIE #38216.

Note - users have reported errors • • - I would look here no matter what you do. Categories are on the left. • - I like this one; a lot of good questions.

ADIsimPE, which is powered by SIMetrix/SIMPLIS, is a circuit simulation suite optimized for the design and development of analog and mixed signal circuits. Aug 25, 2015 - There are a mixed bag of topics the player can browse to go about as a base for every circuit outline. If you want Grand Turismo 5 on your PC,.

• • - A resource with multiple topics. • • - Subnetting practice site built by redditor • - Don't forget to thank and remind him to update his sheets • Looking for work? Check out Must Haves • - The network simulator that every network person should have • • • • • • NOTE: The 'Reddit Cisco Ring', its associates, subreddits, and creator 'mechman991' are not endorsed, sponsored, or officially associated with Cisco Systems Inc.

All opinions stated are those of the poster only, and do not reflect the opinion of Cisco Systems Inc., or its affiliates. PC's and routers transmit on one pair of wires, and listen on another. Switches do this on the opposite pairs. It was presumed long ago that switches or hubs would connect PC's and/or routers together, so this made simple straight-through wiring easy to use, but a problem occurs when you're directly connecting any PC to PC, router to router, or switch to switch because they're essentially talking into each other's mouths. By using a crossover cable, you fix this issue, though if you have a long setup that goes through multiple patch panels, you have to use only one crossover cable and the rest regular straight-through cables (or technically any odd number of crossover cables).

Modern equipment can automatically flip the TX and RX pairs, and thus isn't an issue. This problem also exists on fiber with fiber polarity. Most SFPs transmit on one piece of glass and receive on another, so you have to make sure you don't have two transmitters pointing at each other or it won't work. There's no automatic solution for this (at least in widespread usage). There are also fiber SFP's that only use a single, simplex fiber cable as opposed to a duplex pair; in this case you have two different SFP's, one transmitting at 1310nm, the other at 1550nm, so in this case you have to make sure for every circuit you have one of each type.

I know this one! I'm going off of memory here so some values might be a bit off. PCs, Routers, Switches, etc. All transfer data over copper pairs. One of the wires in a pair transfers and the other receives on the port of the NIC card. PC NIC cards transfer on 1 and 3 pins and receive on 2 and 6 pins.

Sudarshan kriya technique. Kriyā most commonly refers to a 'completed action', technique or practice within a yoga discipline to achieve a specific result.

Switches on the other hand are the opposite (receive on 1 and 3 and transmit on 2 and 6). So when you connect a cable from a PC to a switch, the can use a straight through cable. However, if you want to connect two PCs or two switches together, you may need a crossover cable instead. Note: I say 'may need' because of something called 'auto MDI-X' which allows a switch, for example, to detect that the pins would need to switch roles. I wrote specifically about the 'why' behind crossovers here: The gist of it is. There are two types of NIC's: MDI and MDI-X.

The difference between the two is they each transmit on a different pair of wires. When connecting an MDI nic to an MDI-X nic, the transmit pair correlates to the opposite NIC's receive pair: 'End points' on a network typically use the MDI specification (Hosts, Routers). 'Intermediate' devices on a network typically use the MDI-X specification (Switches, hubs). This makes it so when an endpoint is cabled to an intermediate device, the wire pairs line up perfectly: BUT, when you have two 'like' devices, the wire must introduce a 'crossing of the pairs' so that what is transmitted by one speaker is received by the other: This also includes when two devices with MDI-X NIC's are connected to each other. Note the 'wire' between these two switches also has a crossing of the pairs: • • • • • •.